Cracked panels, warped boards, peeling paint — these are signs your siding is failing before your eyes. Forge Siding delivers professional Siding across Granby, CO with upfront pricing and crews who show up on schedule.
Forge Siding grew out of a simple frustration: too many Granby homeowners were paying good money for Siding work that failed inside five years. Wrong profiles, wrong fastener gauges, no housewrap — then the callbacks never came. We do it right the first time, using manufacturer-recommended installation methods and materials rated for CO's specific climate demands.
Our crews are licensed, carry full general liability and workers' comp, and every lead installer has completed manufacturer certification training. We work with fiber cement, engineered wood, vinyl, and steel systems — and we'll tell you straight which one makes the most sense for your home's structure, your local weather patterns, and your budget. No upselling, no pressure.
Siding doesn't fail overnight — it gives you warning signs first. Catch them early and a repair handles it. Miss them, and you're looking at rot, mold, and structural repairs on top of the siding bill.
Even a small gap at a butt joint or around a window trim is an entry point. Water wicks in, freeze-thaw cycles widen the gap, and the damage compounds every winter.
Panels that bow outward have usually absorbed moisture or were installed without adequate expansion clearance. Warped vinyl or fiber cement can't seal properly at the joints, so the problem accelerates.
Interior peeling close to an outside wall isn't a paint problem — it's a moisture infiltration problem. Your siding is the likely culprit and ignoring it turns a siding job into a drywall and mold job.
Panels that have pulled away from the wall are an open door for pests, moisture, and cold air. Nails back out over time when the substrate is soft — often a sign of prior water damage underneath.
Old or failing siding, particularly if the housewrap underneath has deteriorated, acts like a thermal short-circuit. Your HVAC runs harder to compensate, and the bills reflect it before the siding looks obviously bad.
Extreme fading means UV degradation — the protective surface layer is gone. Chalking on older paint-based systems signals the same. At that stage, the panel is no longer blocking UV penetration to the substrate underneath.
From a single damaged panel to a complete re-side on a large commercial property, we handle the full range of exterior cladding work — and we do it with the same crew standards regardless of job size.
Fiber cement is the workhorse material we recommend most in CO's climate — it handles humidity, impact, and UV better than most alternatives and carries manufacturer warranties that actually hold up. We're certified installers for HardiePlank, HardieShingle, and competing fiber cement systems. Installation follows manufacturer specs to the millimeter: correct lap, correct fastener type and spacing, correct clearance from grade and roof surface, and full housewrap integration on every project.
Done right, vinyl siding is durable, low-maintenance, and cost-effective. Done wrong — wrong gauge, wrong fastener pattern, no expansion clearance — it warps in the heat and pulls loose in wind. We use .044" and .046" gauge panels minimum and follow thermal expansion specs precisely for CO's temperature range. Nail hem fastening at 16" centers, 1/32" expansion gap at all trim terminations, and a fully integrated vinyl accessory system so the corners, J-channel, and window trim all work together.
Engineered wood is popular in Granby neighborhoods where the traditional wood look matters architecturally but the maintenance demands of real cedar or pine aren't practical. We install with stainless or hot-dipped galvanized fasteners to prevent iron staining at the nail head — a detail that separates a professional installation from a quick flip job.
Our repair crews use the same material standards as our full-installation teams — no caulking over gaps as a permanent fix, no missing sealant at transitions, no shortcuts on housewrap at the repair perimeter. If there's rot in the sheathing behind the damaged panel, we address it during the repair rather than covering it up.
Commercial and multi-unit projects have different demands — larger panel formats, longer exposure to foot traffic and equipment contact, stricter fire ratings in some occupancy classes, and coordinated scheduling with other trades. Forge Siding handles commercial cladding projects in Granby, CO with full project management: dedicated site supervisor, daily progress reporting, and material delivery coordinated to minimize storage and laydown area on constrained sites.
Siding that terminates at rotted or missing fascia boards isn't protected — it's channeling water straight into the rafter tails. We routinely pair siding replacement with trim, soffit, and fascia work so the entire exterior envelope is addressed in one mobilization rather than two. PVC trim board, prefinished aluminum coil, and fiber cement fascia are all in our wheelhouse.
We built our process around the two complaints we heard from homeowners most: contractors who didn't communicate, and scopes that changed after signing. Here's exactly how a Forge Siding project runs from start to finish.
A thorough inspection before we quote means the estimate we hand you is accurate. We check the substrate, the existing housewrap or vapor barrier, window and door flashing, corner and soffit condition — all of it — so there are no hidden surprises once demo starts.
You receive a line-by-line written estimate: material cost by product and quantity, labor, removal and disposal of existing siding, and any sheathing repair identified in the assessment. We walk through material options with physical samples, not just catalog photos. You sign off on the spec before we order anything.
Your start date is locked at signing. Crew arrives on time, materials are staged and ready, and the site is protected before demo begins. We run a tight job — no leaving panels exposed overnight when rain is in the forecast.
At project completion, we walk the entire exterior with you. Every run of siding, every corner, every trim termination — you look at it before we close out. If anything isn't right, it gets fixed on the spot. Our goal is that you refer us to your neighbor the week after the project wraps.
We don't sub out work to unlicensed handymen to cut costs. Every installer on a Forge Siding project is a W-2 employee or licensed sub with verified credentials and completed manufacturer training.
You see the number before you sign — and the invoice matches the estimate. If scope changes come up during demo, we stop work, show you what we found, and get written approval before proceeding. No invoice surprises.
When we book your project, we commit to a start date. No bumping you for a bigger job, no weeks of silence after signing. We operate with enough crew capacity to honor the schedule we gave you.
We've seen what happens when crews leave siding debris sitting for a week. Nails in the lawn, panels blocking access, dust in the HVAC intake. Our cleanup protocol runs end-of-day, not end-of-project.
Every Siding project we complete is backed by our written workmanship warranty. If anything we installed fails due to installation error — a panel pulls loose, a trim joint opens, moisture gets in at a transition we sealed — we come back at no charge and fix it. Not a credit, not a partial. Fixed.
Talk to Us About Your Project — +1-844-782-0929Straight from the homeowners we've worked with across Granby and Granby, CO.
We had three other quotes before calling Forge Siding. The difference was the inspection — they actually walked the whole house with a moisture meter and found soft sheathing behind two panels on the north wall that nobody else mentioned. The estimate covered the sheathing repair too, so no surprise charges when demo day came. Final result is clean and tight. We'd hire them again without hesitation.
I manage a twelve-unit building in Granby and we needed LP SmartSide on three facades before winter. Forge Siding coordinated with our property manager, worked around tenant schedules, delivered materials in two staged drops to keep the lot clear, and finished four days ahead of the original schedule. Commercial billing was clean and documented. They're on our preferred vendor list now.
We went with insulated vinyl — Forge Siding recommended the insulated backer for our exposure and the energy savings have been real. First heating season after the install, our gas bill dropped noticeably. Installation crew was professional, on time every day, and the lead installer walked me through every elevation before he called the project done.
I had a specific architectural profile I wanted for the gable ends — a shingle exposure pattern — and everyone else told me it was a custom order with a six-week wait. Forge Siding had it in stock through their regional supplier and we started within two weeks of signing. The detail work at the gable peaks is clean and exact. Not every contractor has the skill to do that level of trim work.
Five-star work across the board. The crew showed up when scheduled, worked efficiently, and the lead walked me around the house at the end of each day so I could see progress and raise any questions before the next morning. The final product is outstanding — tight lap lines, perfect miters at the corners, no nail pops. My neighbor has already asked for Forge Siding's contact information.
I needed a quick turnaround on a rental property before a new tenant moved in. Forge Siding fit us in on short notice, did a clean vinyl replacement on two elevations, and the inspection cleared without a single callback item. Responsive, professional, priced fairly. That's all I ask for and they delivered all three.
We get these questions every week. Here are the honest answers.
We're not a national call center subcontracting your project to whoever's available. Our crews are based in and around Granby, CO. We know local code requirements, local supplier lead times, and local weather patterns — and that local knowledge shows up in how the project runs.
Our primary service area covers Granby and surrounding communities within our regional radius. Call +1-844-782-0929 to confirm service availability at your address — we'll tell you same-day.
Free written estimate. Licensed crew. Scheduled start date. Call Forge Siding now and get a real assessment — not a ballpark number over the phone.
Call +1-844-782-0929 Now